我公司從事濟南裝載機的銷售工作，在市場中得到了廣大客戶的一致好評，下面給大家講解一下濟南裝載機磨合期應該如何維護？
1、注意經常檢查潤滑油、液壓油、冷卻液、制動液以及燃油油(水)位和品質,并注意檢查整機的密封性.檢查中發現油水缺少過多,應分析原因.同時,應強化各潤滑點的潤滑,建議在磨合期內,每班都要對潤滑點加注潤滑脂(特殊要求除外)。
Note that regular checks of lubricating oil, hydraulic oil, coolant, brake fluid and fuel oil (water) bit and the quality and attention to check the tightness of the machine. Inspection found that a lack of too much water, you should analyze the reasons for the same time, should be strengthened lubricate all lubrication points, recommended run-in period, each class must lubrication of lubrication points (except for special requirements).
2、磨合期結束,應對機器進行強制保養,做好檢查和調整工作,同時注意油液的更換和裝載機的維護。
The end of the run-in period, forced to deal with machine maintenance, inspection and adjustment of work to do, while paying attention to fluid replacement and maintenance of loaders.
3、注意經常觀察各儀表指示,出現異常應及時停車予以排除,在原因未找到、故障未排除前應停止作業。
Note that each instrument instruction often observed, abnormalities should be excluded stop in time, the reason is not found, the fault is not ruled out before the operation should be stopped.　　
4、由于工程機械是特殊車輛，操作人員應接受廠家的培訓、指導，對機器的結構、性能有充分的了解，并獲得一定的操作及維護經驗方可操作機器。生產廠家提供的《產品使用維護說明書》是操作者操作設備的必備資料,在操作機器前,一定要先閱讀《使用維護說明書》,按要求進行操作保養。
Because of construction machinery is a special vehicle, the operator should receive factory training, guidance, structure of the machine, the performance has a full understanding of, and access to certain operating and maintenance experience before operating the machine. Manufacturers to provide "product maintenance manual" is the operator to operate the equipment necessary information before operating the machine, be sure to read the "maintenance manual", according to the requirements of operation and maintenance.　　
5、保持機器清潔,及時調整、緊固松動的零部件以防因松動而加劇零部件的磨損或?qū)е铝悴考G失。
Keep the machine clean, timely adjustment, tighten loose parts to prevent loosening due to increased wear of parts or cause parts missing.　　
6、注意磨合期的工作負荷,磨合期內的工作負荷一半不要超過額定工作負荷的60%,并要安排適合的工作量,防止機器長時間連續作業所引起的過熱現場的發生。
Note that the workload of the run, the run-in period, half of the workload should not exceed 60% of the rated working load, and to arrange for appropriate workload, long continuous operation to prevent the machine from overheating caused by the occurrence of the scene.　　

公司視產品質量為企業生命,十分注重產品的研發和創新,強化質量保障體系,加強質量檢測和監控，受到了廣大用戶的一致好評，我們永保機械值得您的信賴,期待與您的合作。

濟南裝載機：http://m.hpize.cn/